CUSTOM BUILT TRUCK SHELTERS

Rotary Products Custom Truck Shelters allow full access of docked trailers, unlike a Compression Seal which may take up some space on the sides due to the pad overlapping the truck opening.

Rotary Products Truck Shelters are the best in the industry. The lumber is treated for all weather conditions, and Rotary Products has gone the extra mile by using Six support trusses on each side of the shelter in lei of the standard industry specs of only Four. We design our shelters for lasting strength, and durability by adding steel angles in every corner of construction. These steel angle brackets, and our high tear duroprene vinyl curtains make our product the best in the industry!

Truck Shelter Specs

A full access, rigid shelter, with light-transmitting panels in top and sides. With 2" x 4" and 2" x 6" treated wood frame pieces. Bumpers of heavy steel protect the unit. The header and vertical curtains with steel stays are heavy vinyl laminated, reinforced fabric and heavy fabric overlays on the wear areas. The header curtain height is 3'; the front opening is 7'6" W x 8' H; and the overall size is 11'6" x 11' x either 18", 24" or 30" deep.

With the dock height at 4', the shelter will accommodate carriers 12' to 13'6" high. Units are designed to accommodate trucks 8' wide as well as the newer 8'6" wide trucks.

SH402 TRUCK SHELTER
GENERAL SPECIFICATIONS

STANDARD PROJECTIONS

SH402-18	18"	PROJECTION
SH402-24	24"	PROJECTION
SH402-30	30"	PROJECTION
SH402-36	36"	PROJECTION
SH402-42	42"	PROJECTION

STANDARD DIMENSION: 11'6" WIDE X 11'0" HIGH OUTSIDE TO OUTSIDE.

FRAME: Vertical frame members shall be constructed of 2" x 4" preservative treated lumber. Complete with six 2" x 4" wood braces in each vertical member. Vertical members are to have four 1/8" x 1" x 3" zinc plated flat brackets and four 1 1/2 " x 1 1/2" x 3" zinc plated angle brackets for support. Standard vertical frame is 10'6" long or equal to door height on doors higher than 10'6". Translucent light panels shall cover the outside of the frame completely. Header frame shall be constructed of 2" x 4" and 2" x 6" preservative treated lumber. Header frame is sloped 2" for water to run off. Unit complete with six 2" x 4" and one 2" x 6" wood braces. Header frame to have one 1 1/2" x 1 1/2" x 3" zinc plated angle at each corner for reinforcement. Standard header frame is 11'6" long or equal to door width wider than 11'6". Translucent light panel shall cover the top of the header frame completely.

COVER: Vertical covers shall be constructed primarily of 40 oz. per square yard vinyl coated polyester with high tear duroprene vinyl coated polyester at the high wear areas. Included in high wear areas are 22" x 20" reinforced flaps at the bottom vertical covers. A 4" strip down the inside edge of each vertical and 3" strips covering the spring steel stays. Each vertical cover to have seven spring steel stays (.042 x 2" x 24"). Vertical covers to have 3" yellow guide stripe to run the entire length.
Header Cover shall be constructed primarily of 40 oz. per square yard vinyl coated nylon. Reinforced with high tear duroprene at high wear areas. Included in high wear areas are four 11" x 28" high tear duroprene wear shields on each side. Wear shields have extra wide design to accommodate trucks from 7' to 8'6" wide. The high tear duroprene is also used to cover the spring stays. Header cover to include four spring stays (.042 x 2" x 30").

BOTTOM CORNER PILLOWS: There shall be two bottom corner pillows per unit. Bottom cover pillows shall be constructed of polyurethane foam core, covered by 22 oz. vinyl coated nylon with a preservative treated lumber back. Each bottom corner pillow is complete with two galvanized brackets and is designed for easy replacement requiring no tools.

STEEL BUMPERS: Steel bumpers are constructed of 4" square tubes x 11" gauge. Bumpers shall have a 2/16" x 6" x 24" backer plate with four 17/32" holes for mounting. Bumpers shall have a knee brace of 3/8" x 1 1/4" x 24" flat steel and a "C" channel face plate 6" x 12" weighing 8.2 lbs per foot.